/*
* linux/mtio.h header file for Linux. Written by H. Bergman
*
* Modified for special ioctls provided by zftape in September 1997
* by C.-J. Heine.
*/
#ifndef _LINUX_MTIO_H
#define _LINUX_MTIO_H
#include <linux/types.h>
#include <linux/ioctl.h>
/*
* Structures and definitions for mag tape io control commands
*/
/* structure for MTIOCTOP - mag tape op command */
struct mtop {
short mt_op; /* operations defined below */
int mt_count; /* how many of them */
};
/* Magnetic Tape operations [Not all operations supported by all drivers]: */
#define MTRESET 0 /* +reset drive in case of problems */
#define MTFSF 1 /* forward space over FileMark,
* position at first record of next file
*/
#define MTBSF 2 /* backward space FileMark (position before FM) */
#define MTFSR 3 /* forward space record */
#define MTBSR 4 /* backward space record */
#define MTWEOF 5 /* write an end-of-file record (mark) */
#define MTREW 6 /* rewind */
#define MTOFFL 7 /* rewind and put the drive offline (eject?) */
#define MTNOP 8 /* no op, set status only (read with MTIOCGET) */
#define MTRETEN 9 /* retension tape */
#define MTBSFM 10 /* +backward space FileMark, position at FM */
#define MTFSFM 11 /* +forward space FileMark, position at FM */
#define MTEOM 12 /* goto end of recorded media (for appending files).
* MTEOM positions after the last FM, ready for
* appending another file.
*/
#define MTERASE 13 /* erase tape -- be careful! */
#define MTRAS1 14 /* run self test 1 (nondestructive) */
#define MTRAS2 15 /* run self test 2 (destructive) */
#define MTRAS3 16 /* reserved for self test 3 */
#define MTSETBLK 20 /* set block length (SCSI) */
#define MTSETDENSITY 21 /* set tape density (SCSI) */
#define MTSEEK 22 /* seek to block (Tandberg, etc.) */
#define MTTELL 23 /* tell block (Tandberg, etc.) */
#define MTSETDRVBUFFER 24 /* set the drive buffering according to SCSI-2 */
/* ordinary buffered operation with code 1 */
#define MTFSS 25 /* space forward over setmarks */
#define MTBSS 26 /* space backward over setmarks */
#define MTWSM 27 /* write setmarks */
#define MTLOCK 28 /* lock the drive door */
#define MTUNLOCK 29 /* unlock the drive door */
#define MTLOAD 30 /* execute the SCSI load command */
#define MTUNLOAD 31 /* execute the SCSI unload command */
#define MTCOMPRESSION 32/* control compression with SCSI mode page 15 */
#define MTSETPART 33 /* Change the active tape partition */
#define MTMKPART 34 /* Format the tape with one or two partitions */
/* structure for MTIOCGET - mag tape get status command */
struct mtget {
long mt_type; /* type of magtape device */
long mt_resid; /* residual count: (not sure)
* number of bytes ignored, or
* number of files not skipped, or
* number of records not skipped.
*/
/* the following registers are device dependent */
long mt_dsreg; /* status register */
long mt_gstat; /* generic (device independent) status */
long mt_erreg; /* error register */
/* The next two fields are not always used */
__kernel_daddr_t mt_fileno; /* number of current file on tape */
__kernel_daddr_t mt_blkno; /* current block number */
};
/*
* Constants for mt_type. Not all of these are supported,
* and these are not all of the ones that are supported.
*/
#define MT_ISUNKNOWN 0x01
#define MT_ISQIC02 0x02 /* Generic QIC-02 tape streamer */
#define MT_ISWT5150 0x03 /* Wangtek 5150EQ, QIC-150, QIC-02 */
#define MT_ISARCHIVE_5945L2 0x04 /* Archive 5945L-2, QIC-24, QIC-02? */
#define MT_ISCMSJ500 0x05 /* CMS Jumbo 500 (QIC-02?) */
#define MT_ISTDC3610 0x06 /* Tandberg 6310, QIC-24 */
#define MT_ISARCHIVE_VP60I 0x07 /* Archive VP60i, QIC-02 */
#define MT_ISARCHIVE_2150L 0x08 /* Archive Viper 2150L */
#define MT_ISARCHIVE_2060L 0x09 /* Archive Viper 2060L */
#define MT_ISARCHIVESC499 0x0A /* Archive SC-499 QIC-36 controller */
#define MT_ISQIC02_ALL_FEATURES 0x0F /* Generic QIC-02 with all features */
#define MT_ISWT5099EEN24 0x11 /* Wangtek 5099-een24, 60MB, QIC-24 */
#define MT_ISTEAC_MT2ST 0x12 /* Teac MT-2ST 155mb drive, Teac DC-1 card (Wangtek type) */
#define MT_ISEVEREX_FT40A 0x32 /* Everex FT40A (QIC-40) */
#define MT_ISDDS1 0x51 /* DDS device without partitions */
#define MT_ISDDS2 0x52 /* DDS device with partitions */
#define MT_ISONSTREAM_SC 0x61 /* OnStream SCSI tape drives (SC-x0)
and SCSI emulated (DI, DP, USB) */
#define MT_ISSCSI1 0x71 /* Generic ANSI SCSI-1 tape unit */
#define MT_ISSCSI2 0x72 /* Generic ANSI SCSI-2 tape unit */
/* QIC-40/80/3010/3020 ftape supported drives.
* 20bit vendor ID + 0x800000 (see ftape-vendors.h)
*/
#define MT_ISFTAPE_UNKNOWN 0x800000 /* obsolete */
#define MT_ISFTAPE_FLAG 0x800000
/* structure for MTIOCPOS - mag tape get position command */
struct mtpos {
long mt_blkno; /* current block number */
};
/* mag tape io control commands */
#define MTIOCTOP _IOW('m', 1, struct mtop) /* do a mag tape op */
#define MTIOCGET _IOR('m', 2, struct mtget) /* get tape status */
#define MTIOCPOS _IOR('m', 3, struct mtpos) /* get tape position */
/* Generic Mag Tape (device independent) status macros for examining
* mt_gstat -- HP-UX compatible.
* There is room for more generic status bits here, but I don't
* know which of them are reserved. At least three or so should
* be added to make this really useful.
*/
#define GMT_EOF(x) ((x) & 0x80000000)
#define GMT_BOT(x) ((x) & 0x40000000)
#define GMT_EOT(x) ((x) & 0x20000000)
#define GMT_SM(x) ((x) & 0x10000000) /* DDS setmark */
#define GMT_EOD(x) ((x) & 0x08000000) /* DDS EOD */
#define GMT_WR_PROT(x) ((x) & 0x04000000)
/* #define GMT_ ? ((x) & 0x02000000) */
#define GMT_ONLINE(x) ((x) & 0x01000000)
#define GMT_D_6250(x) ((x) & 0x00800000)
#define GMT_D_1600(x) ((x) & 0x00400000)
#define GMT_D_800(x) ((x) & 0x00200000)
/* #define GMT_ ? ((x) & 0x00100000) */
/* #define GMT_ ? ((x) & 0x00080000) */
#define GMT_DR_OPEN(x) ((x) & 0x00040000) /* door open (no tape) */
/* #define GMT_ ? ((x) & 0x00020000) */
#define GMT_IM_REP_EN(x) ((x) & 0x00010000) /* immediate report mode */
#define GMT_CLN(x) ((x) & 0x00008000) /* cleaning requested */
/* 15 generic status bits unused */
/* SCSI-tape specific definitions */
/* Bitfield shifts in the status */
#define MT_ST_BLKSIZE_SHIFT 0
#define MT_ST_BLKSIZE_MASK 0xffffff
#define MT_ST_DENSITY_SHIFT 24
#define MT_ST_DENSITY_MASK 0xff000000
#define MT_ST_SOFTERR_SHIFT 0
#define MT_ST_SOFTERR_MASK 0xffff
/* Bitfields for the MTSETDRVBUFFER ioctl */
#define MT_ST_OPTIONS 0xf0000000
#define MT_ST_BOOLEANS 0x10000000
#define MT_ST_SETBOOLEANS 0x30000000
#define MT_ST_CLEARBOOLEANS 0x40000000
#define MT_ST_WRITE_THRESHOLD 0x20000000
#define MT_ST_DEF_BLKSIZE 0x50000000
#define MT_ST_DEF_OPTIONS 0x60000000
#define MT_ST_TIMEOUTS 0x70000000
#define MT_ST_SET_TIMEOUT (MT_ST_TIMEOUTS | 0x000000)
#define MT_ST_SET_LONG_TIMEOUT (MT_ST_TIMEOUTS | 0x100000)
#define MT_ST_SET_CLN 0x80000000
#define MT_ST_BUFFER_WRITES 0x1
#define MT_ST_ASYNC_WRITES 0x2
#define MT_ST_READ_AHEAD 0x4
#define MT_ST_DEBUGGING 0x8
#define MT_ST_TWO_FM 0x10
#define MT_ST_FAST_MTEOM 0x20
#define MT_ST_AUTO_LOCK 0x40
#define MT_ST_DEF_WRITES 0x80
#define MT_ST_CAN_BSR 0x100
#define MT_ST_NO_BLKLIMS 0x200
#define MT_ST_CAN_PARTITIONS 0x400
#define MT_ST_SCSI2LOGICAL 0x800
#define MT_ST_SYSV 0x1000
#define MT_ST_NOWAIT 0x2000
#define MT_ST_SILI 0x4000
/* The mode parameters to be controlled. Parameter chosen with bits 20-28 */
#define MT_ST_CLEAR_DEFAULT 0xfffff
#define MT_ST_DEF_DENSITY (MT_ST_DEF_OPTIONS | 0x100000)
#define MT_ST_DEF_COMPRESSION (MT_ST_DEF_OPTIONS | 0x200000)
#define MT_ST_DEF_DRVBUFFER (MT_ST_DEF_OPTIONS | 0x300000)
/* The offset for the arguments for the special HP changer load command. */
#define MT_ST_HPLOADER_OFFSET 10000
#endif /* _LINUX_MTIO_H */