READ
Section: Linux Programmer's Manual (2)
Updated: 2009-02-23
NAME
read - read from a file descriptor
SYNOPSIS
#include <unistd.h>
ssize_t read(int fd, void *buf, size_t count);
DESCRIPTION
read()
attempts to read up to
count
bytes from file descriptor
fd
into the buffer starting at
buf.
If
count
is zero,
read()
returns zero and has no other results.
If
count
is greater than
SSIZE_MAX,
the result is unspecified.
RETURN VALUE
On success, the number of bytes read is returned (zero indicates end of
file), and the file position is advanced by this number.
It is not an error if this number is smaller than the number of bytes
requested; this may happen for example because fewer bytes are actually
available right now (maybe because we were close to end-of-file, or
because we are reading from a pipe, or from a terminal), or because
read()
was interrupted by a signal.
On error, -1 is returned, and
errno
is set appropriately.
In this case it is left unspecified whether
the file position (if any) changes.
ERRORS
- EAGAIN
-
The file descriptor
fd
refers to a file other than a socket and has been marked nonblocking
(O_NONBLOCK),
and the read would block.
- EAGAIN or EWOULDBLOCK
-
The file descriptor
fd
refers to a socket and has been marked nonblocking
(O_NONBLOCK),
and the read would block.
POSIX.1-2001 allows either error to be returned for this case,
and does not require these constants to have the same value,
so a portable application should check for both possibilities.
- EBADF
-
fd
is not a valid file descriptor or is not open for reading.
- EFAULT
-
buf
is outside your accessible address space.
- EINTR
-
The call was interrupted by a signal before any data was read; see
signal(7).
- EINVAL
-
fd
is attached to an object which is unsuitable for reading;
or the file was opened with the
O_DIRECT
flag, and either the address specified in
buf,
the value specified in
count,
or the current file offset is not suitably aligned.
- EINVAL
-
fd
was created via a call to
timerfd_create(2)
and the wrong size buffer was given to
read();
see
timerfd_create(2)
for further information.
- EIO
-
I/O error.
This will happen for example when the process is in a
background process group, tries to read from its controlling tty,
and either it is ignoring or blocking
SIGTTIN
or its process group
is orphaned.
It may also occur when there is a low-level I/O error
while reading from a disk or tape.
- EISDIR
-
fd
refers to a directory.
Other errors may occur, depending on the object connected to
fd.
POSIX allows a
read()
that is interrupted after reading some data
to return -1 (with
errno
set to
EINTR)
or to return the number of bytes already read.
CONFORMING TO
SVr4, 4.3BSD, POSIX.1-2001.
NOTES
On NFS file systems, reading small amounts of data will only update the
timestamp the first time, subsequent calls may not do so.
This is caused
by client side attribute caching, because most if not all NFS clients
leave st_atime (last file access time)
updates to the server and client side reads satisfied from the
client's cache will not cause st_atime updates on the server as there are no
server side reads.
Unix semantics can be obtained by disabling client
side attribute caching, but in most situations this will substantially
increase server load and decrease performance.
Many file systems and disks were considered to be fast enough that the
implementation of
O_NONBLOCK
was deemed unnecessary.
So,
O_NONBLOCK
may not be available on files
and/or disks.
SEE ALSO
close(2),
fcntl(2),
ioctl(2),
lseek(2),
open(2),
pread(2),
readdir(2),
readlink(2),
readv(2),
select(2),
write(2),
fread(3)
COLOPHON
This page is part of release 3.27 of the Linux
man-pages
project.
A description of the project,
and information about reporting bugs,
can be found at
http://www.kernel.org/doc/man-pages/.
Index
- NAME
-
- SYNOPSIS
-
- DESCRIPTION
-
- RETURN VALUE
-
- ERRORS
-
- CONFORMING TO
-
- NOTES
-
- SEE ALSO
-
- COLOPHON
-
This document was created by
man2html,
using the manual pages.
Time: 07:34:57 GMT, March 26, 2013